描述

幾天前，我從童年時代發現了一輛漂亮的遙控車，但它的遙控器壞了，所以我想為什么不把這輛車改裝成高速 Arduino 遙控車。

所以現在就在這里，我已經把它變成了一輛高速 Arduino 遙控車，今天我將與你分享我是如何做到的。我用于這個項目的應用程序可以從這里下載。

高速 Arduino 遙控車的功能

這款高速 Arduino 遙控車的功能如下

• 前燈
• 背光燈
• 中心的 RGB 燈會讓它看起來不錯
• 喇叭
• 全方位旋轉
• 速度控制

所需組件

高速 Arduino 遙控車所需的組件如下

• 帶電機的舊車
• 阿杜諾
• HC-05 或 HC-06 藍牙模塊
• L298N電機驅動器
• 蜂鳴器
• RGB LED
• 2 個紅色 LED
• 2 個白色 LED
• 2 X 3.7V 可充電電池
• 9V電池
• 7 X 220 歐姆電阻

硬件

我使用了兩個 3.7V 的可充電電池來運行這些電機。這些電池可以反復使用，也可以快速運行電機。

如果您想了解更多關于 Arduino 與 RGB 模塊接口的信息，請閱讀本教程 | Arduino RGB LED 教程

如果您想了解更多關于藍牙模塊與 Arduino 接口的信息，請閱讀本教程 | Arduino藍牙模塊教程

?

?

按照上面的電路圖完成所有連接后，我的汽車連接電路如下圖所示。

?

?

?

?

將頂部車身安裝在其上后，這輛車看起來就像一輛原始的蘭博基尼。中間連接的RGB讓它看起來更漂亮，它的高速使它可以與市場上的遙控車競爭。

?

?

?

?

?

?

代碼

//including the libraries
#include  // TX RX software library for bluetooth
#include 
//Defining pins for RGB led
#define GREEN 13
#define BLUE 5
#define RED 4
#define delayTime 3
#define LED_NUM 3
LEDFader leds[LED_NUM] = {
  LEDFader(4),
  LEDFader(5),
  LEDFader(13)
};
//Initializing pins for bluetooth Module
int bluetoothTx = 2; // bluetooth tx to 2 pin
int bluetoothRx = 3; // bluetooth rx to 3 pin
SoftwareSerial bluetooth(bluetoothTx, bluetoothRx);
//Front Motor Pins  
int Enable1 = 6;
int Motor1_Pin1 = 7;  
int Motor1_Pin2 = 8;  
//Back Motor Pins      
int Motor2_Pin1 = 9; 
int Motor2_Pin2 = 10;
int Enable2 = 11; 
//Front Light pins   
int front_light1 = A0;
int front_light2 = A1;
//Back light pins
int back_light1 = A2;
int back_light2 = A3;
int horn = 12;
char command ; //variable to store the data
int velocity = 0; //Variable to control the speed of motor
void setup() 
{       
  //Set the baud rate of serial communication and bluetooth module at same rate.
  Serial.begin(9600);  
  bluetooth.begin(9600);
  //Setting the L298N, LED and RGB LED pins as output pins.
  pinMode(Motor1_Pin1, OUTPUT);  
  pinMode(Motor1_Pin2, OUTPUT);
  pinMode(Enable1, OUTPUT);
  pinMode(Motor2_Pin1, OUTPUT);  
  pinMode(Motor2_Pin2, OUTPUT);
  pinMode(Enable2, OUTPUT); 
  pinMode(front_light1, OUTPUT);  
  pinMode(back_light1, OUTPUT);
  pinMode(front_light2, OUTPUT);  
  pinMode(back_light2, OUTPUT);
  pinMode(horn, OUTPUT);
  pinMode(GREEN, OUTPUT);
  pinMode(BLUE, OUTPUT);
  pinMode(RED, OUTPUT);
  //Setting the enable and RGB LED pins as HIGH.
  digitalWrite(Enable1, HIGH);
  digitalWrite(Enable2, HIGH);
  digitalWrite(GREEN, HIGH);
  digitalWrite(BLUE, HIGH);
  digitalWrite(RED, HIGH);
}
void loop(){
  if(bluetooth.available() > 0){  //Checking if there is some data available or not
    command = bluetooth.read();   //Storing the data in the 'command' variable
    Serial.println(command);      //Printing it on the serial monitor
    
    //Change pin mode only if new command is different from previous.   
    switch(command){
    case 'F':  //Moving the Car Forward
      digitalWrite(Motor2_Pin2, LOW);
      digitalWrite(Motor2_Pin1, HIGH);
      digitalWrite(Motor1_Pin1, LOW);
      digitalWrite(Motor1_Pin2, LOW);
      break;
    case 'B':  //Moving the Car Backward
      digitalWrite(Motor2_Pin1, LOW);
      digitalWrite(Motor2_Pin2, HIGH);
      digitalWrite(Motor1_Pin1, LOW);
      digitalWrite(Motor1_Pin2, LOW);
      break;
    case 'L':  //Moving the Car Left
      digitalWrite(Motor1_Pin1, LOW);
      digitalWrite(Motor1_Pin2, HIGH);
      digitalWrite(Motor2_Pin1, LOW);
      digitalWrite(Motor2_Pin2, LOW);
      break;
    case 'R':   //Moving the Car Right
      digitalWrite(Motor1_Pin2, LOW);
      digitalWrite(Motor1_Pin1, HIGH);  
      digitalWrite(Motor2_Pin1, LOW);
      digitalWrite(Motor2_Pin2, LOW);
      break;
    case 'S':   //Stop
      digitalWrite(Motor2_Pin2, LOW);
      digitalWrite(Motor2_Pin1, LOW);
      digitalWrite(Motor1_Pin2, LOW);
      digitalWrite(Motor1_Pin1, LOW);
      break; 
    case 'I':  //Moving the Car Forward right
      digitalWrite(Motor2_Pin2, LOW);
      digitalWrite(Motor2_Pin1, HIGH);
      digitalWrite(Motor1_Pin2, LOW);
      digitalWrite(Motor1_Pin1, HIGH);
      break; 
    case 'J':  //Moving the Car backward right
      digitalWrite(Motor1_Pin2, LOW);
      digitalWrite(Motor1_Pin1, HIGH);
      digitalWrite(Motor2_Pin1, LOW);
      digitalWrite(Motor2_Pin2, HIGH);
      break;        
    case 'G':  //Moving the Car Forward left
      digitalWrite(Motor2_Pin2, LOW);
      digitalWrite(Motor2_Pin1, HIGH);
      digitalWrite(Motor1_Pin1, LOW);
      digitalWrite(Motor1_Pin2, HIGH);
      break; 
    case 'H':  //Moving the Car backward left
      digitalWrite(Motor2_Pin1, LOW);
      digitalWrite(Motor2_Pin2, HIGH);
      digitalWrite(Motor1_Pin1, LOW);
      digitalWrite(Motor1_Pin2, HIGH);
      break;
    case 'W':  //Front light ON 
      digitalWrite(front_light1, HIGH);
      digitalWrite(front_light2, HIGH);
      break;
    case 'w':  //Front light OFF
      digitalWrite(front_light1, LOW);
      digitalWrite(front_light2, LOW);
      break;
    case 'U':  //Back light ON 
      digitalWrite(back_light1, HIGH);
      digitalWrite(back_light2, HIGH);
      break;
    case 'u':  //Back light OFF 
      digitalWrite(back_light1, LOW);
      digitalWrite(back_light2, LOW);
      break; 
    case 'V':  //Horn On
      tone(horn,494);
      break; 
    case 'v':  //Horn OFF 
       noTone(horn);
      break;   
    case 'x': //Turn ON Everything
    break;
    case 'X': //Turn OFF Everything
      
    break;
    //Controlling the Speed of Car  
    default:  //Get velocity
      if(command=='q'){
        velocity = 255;  //Full velocity
        analogWrite(Enable2, velocity);
      }
      else{ 
        //Chars '0' - '9' have an integer equivalence of 48 - 57, accordingly.
        if((command >= 48) && (command <= 57)){ 
          //Subtracting 48 changes the range from 48-57 to 0-9.
          //Multiplying by 25 changes the range from 0-9 to 0-225.
          velocity = (command - 48)*25;       
          analogWrite(Enable2, velocity);
        }
      }
      }
    }
     RGB();
  } 
  void RGB()
{
    // Update all LEDs and start new fades if any are done
  for (byte i = 0; i < LED_NUM; i++) 
  {
    LEDFader *led = &leds[i];
    led->update();
    // This LED is not fading, start a new fade
    if (led->is_fading() == false) 
    {
      int duration = random(1000, 3000); // between 1 - 3 seconds
      // Fade Up
      if (led->get_value() == 0) 
      {
        byte intensity = random(100, 255);
        led->fade(intensity, duration);
      }
      // Fade Down
      else 
      {
        led->fade(0, duration);
      }
    }
  }
 }

?

?