一、概述

基于子系統去開發驅動程序已經是linux內核中普遍的做法了。前面寫過基于I2C子系統的驅動開發。本文介紹另外一種常用總線SPI的開發方法。SPI子系統的開發和I2C有很多的相似性，大家可以對比學習。本主題分為兩個部分?jǐn)⑹觯谝徊糠纸榻B基于SPI子系統開發的理論框架；第二部分以華清遠見教學平臺FS_S5PC100上的M25P10芯片為例（內核版本2.6.29），編寫一個SPI驅動程序

一、概述

基于子系統去開發驅動程序已經是linux內核中普遍的做法了。前面寫過基于I2C子系統的驅動開發。本文介紹另外一種常用總線SPI的開發方法。SPI子系統的開發和I2C有很多的相似性，大家可以對比學習。本主題分為兩個部分?jǐn)⑹?，第一部分介紹基于SPI子系統開發的理論框架；第二部分以華清遠見教學平臺FS_S5PC100上的M25P10芯片為例（內核版本2.6.29），編寫一個SPI驅動程序?qū)嵗?/p>

二、SPI總線協議簡介

介紹驅動開發前，需要先熟悉下SPI通訊協議中的幾個關鍵的地方，后面在編寫驅動時，需要考慮相關因素。

SPI總線由MISO（串行數據輸入）、MOSI（串行數據輸出）、SCK（串行移位時鐘）、CS（使能信號）4個信號線組成。如FS_S5PC100上的M25P10芯片接線為：

上圖中M25P10的D腳為它的數據輸入腳，Q為數據輸出腳，C為時鐘腳。

SPI常用四種數據傳輸模式，主要差別在于：輸出串行同步時鐘極性（CPOL）和相位（CPHA）可以進行配置。如果CPOL= 0，串行同步時鐘的空閑狀態為低電平；如果CPOL= 1，串行同步時鐘的空閑狀態為高電平。如果CPHA= 0，在串行同步時鐘的前沿（上升或下降）數據被采樣；如果CPHA = 1，在串行同步時鐘的后沿（上升或下降）數據被采樣。

這四種模式中究竟選擇哪種模式取決于設備。如M25P10的手冊中明確它可以支持的兩種模式為：CPOL=0 CPHA=0? 和 CPOL=1 CPHA=1

三、linux下SPI驅動開發

首先明確SPI驅動層次，如下圖：???????

我們以上面的這個圖為思路

1、 Platform bus

Platform bus對應的結構是platform_bus_type，這個內核開始就定義好的。我們不需要定義。

2、Platform_device

SPI控制器對應platform_device的定義方式，同樣以S5PC100中的SPI控制器為例，參看arch/arm/plat-s5pc1xx/dev-spi.c文件

點擊(此處)折疊或打開

struct platform_device s3c_device_spi0?=?{

.name?=?"s3c64xx-spi",?//名稱，要和Platform_driver匹配

.id?=?0,?//第0個控制器，S5PC100中有3個控制器

.num_resources?=?ARRAY_SIZE(s5pc1xx_spi0_resource),?//占用資源的種類

.resource?=?s5pc1xx_spi0_resource,?//指向資源結構數組的指針

.dev?=?{

.dma_mask?=?&spi_dmamask,?//dma尋址范圍?

.coherent_dma_mask?=?DMA_BIT_MASK(32),?//可以通過關閉cache等措施保證一致性的dma尋址范圍

.platform_data?=?&s5pc1xx_spi0_pdata,?//特殊的平臺數據，參看后文

},

};

static struct s3c64xx_spi_cntrlr_info s5pc1xx_spi0_pdata?=?{

.cfg_gpio?=?s5pc1xx_spi_cfg_gpio,?//用于控制器管腳的IO配置

.fifo_lvl_mask?=?0x7f,

.rx_lvl_offset?=?13,

};

static?int?s5pc1xx_spi_cfg_gpio(struct platform_device?*pdev)

{

switch?(pdev->id)?{

case?0:

s3c_gpio_cfgpin(S5PC1XX_GPB(0),?S5PC1XX_GPB0_SPI_MISO0);

s3c_gpio_cfgpin(S5PC1XX_GPB(1),?S5PC1XX_GPB1_SPI_CLK0);

s3c_gpio_cfgpin(S5PC1XX_GPB(2),?S5PC1XX_GPB2_SPI_MOSI0);

s3c_gpio_setpull(S5PC1XX_GPB(0),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPB(1),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPB(2),?S3C_GPIO_PULL_UP);

break;

case?1:

s3c_gpio_cfgpin(S5PC1XX_GPB(4),?S5PC1XX_GPB4_SPI_MISO1);

s3c_gpio_cfgpin(S5PC1XX_GPB(5),?S5PC1XX_GPB5_SPI_CLK1);

s3c_gpio_cfgpin(S5PC1XX_GPB(6),?S5PC1XX_GPB6_SPI_MOSI1);

s3c_gpio_setpull(S5PC1XX_GPB(4),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPB(5),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPB(6),?S3C_GPIO_PULL_UP);

break;

case?2:

s3c_gpio_cfgpin(S5PC1XX_GPG3(0),?S5PC1XX_GPG3_0_SPI_CLK2);

s3c_gpio_cfgpin(S5PC1XX_GPG3(2),?S5PC1XX_GPG3_2_SPI_MISO2);

s3c_gpio_cfgpin(S5PC1XX_GPG3(3),?S5PC1XX_GPG3_3_SPI_MOSI2);

s3c_gpio_setpull(S5PC1XX_GPG3(0),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPG3(2),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPG3(3),?S3C_GPIO_PULL_UP);

break;

default:

dev_err(&pdev->dev,?"Invalid SPI Controller number!");

return?-EINVAL;

}

3、Platform_driver

再看platform_driver，參看drivers/spi/spi_s3c64xx.c文件

點擊(此處)折疊或打開

static struct platform_driver s3c64xx_spi_driver?=?{

.driver?=?{

.name?=?"s3c64xx-spi",?//名稱，和platform_device對應

.owner?=?THIS_MODULE,

},

.remove?=?s3c64xx_spi_remove,

.suspend?=?s3c64xx_spi_suspend,

.resume?=?s3c64xx_spi_resume,

};

platform_driver_probe(&s3c64xx_spi_driver,?s3c64xx_spi_probe)；//注冊s3c64xx_spi_driver

和平臺中注冊的platform_device匹配后，調用s3c64xx_spi_probe。然后根據傳入的platform_device參數，構建一個用于描述SPI控制器的結構體spi_master，并注冊。spi_register_master(master)。后續注冊的spi_device需要選定自己的spi_master，并利用spi_master提供的傳輸功能傳輸spi數據。

和I2C類似，SPI也有一個描述控制器的對象叫spi_master。其主要成員是主機控制器的序號（系統中可能存在多個SPI主機控制器）、片選數量、SPI模式和時鐘設置用到的函數、數據傳輸用到的函數等。

點擊(此處)折疊或打開

struct spi_master?{

struct device dev;

s16 bus_num;?//表示是SPI主機控制器的編號。由平臺代碼決定

u16 num_chipselect;?//控制器支持的片選數量，即能支持多少個spi設備

int?(*setup)(struct spi_device?*spi);?//針對設備設置SPI的工作時鐘及數據傳輸模式等。在spi_add_device函數中調用。

int?(*transfer)(struct spi_device?*spi,

struct spi_message?*mesg);?//實現數據的雙向傳輸，可能會睡眠

void?(*cleanup)(struct spi_device?*spi);?//注銷時調用

};

4、Spi bus

Spi總線對應的總線類型為spi_bus_type，在內核的drivers/spi/spi.c中定義

點擊(此處)折疊或打開

struct bus_type spi_bus_type?=?{

.name?=?"spi",

.dev_attrs?=?spi_dev_attrs,

.match?=?spi_match_device,

.uevent?=?spi_uevent,

.suspend?=?spi_suspend,

.resume?=?spi_resume,

};

對應的匹配規則是（高版本中的匹配規則會稍有變化，引入了id_table，可以匹配多個spi設備名稱）：

點擊(此處)折疊或打開

static?int?spi_match_device(struct device?*dev,?struct device_driver?*drv)

{

const?struct spi_device?*spi?=?to_spi_device(dev);

return strcmp(spi->modalias,?drv->name)?==?0;

}

5、spi_device

下面該講到spi_device的構建與注冊了。spi_device對應的含義是掛接在spi總線上的一個設備，所以描述它的時候應該明確它自身的設備特性、傳輸要求、及掛接在哪個總線上。

點擊(此處)折疊或打開

static struct spi_board_info s3c_spi_devs[]?__initdata?=?{

{

.modalias?=?"m25p10",

.mode?=?SPI_MODE_0,?//CPOL=0,?CPHA=0 此處選擇具體數據傳輸模式

.max_speed_hz?=?10000000,?//最大的spi時鐘頻率

/*?Connected?to?SPI-0 as 1st Slave?*/

.bus_num?=?0,?//設備連接在spi控制器0上

.chip_select?=?0,?//片選線號，在S5PC100的控制器驅動中沒有使用它作為片選的依據，而是選擇了下文controller_data里的方法。

.controller_data?=?&smdk_spi0_csi[0],

},

};

static struct s3c64xx_spi_csinfo smdk_spi0_csi[]?=?{

[0]?=?{

.set_level?=?smdk_m25p10_cs_set_level,

.fb_delay?=?0x3,

},

};

static void smdk_m25p10_cs_set_level(int?high)?//spi控制器會用這個方法設置cs

{

u32 val;

val?=?readl(S5PC1XX_GPBDAT);

if?(high)

val?|=?(1<<3);

else

val?&=?~(1<<3);

writel(val,?S5PC1XX_GPBDAT);

}

spi_register_board_info(s3c_spi_devs,?ARRAY_SIZE(s3c_spi_devs));//注冊spi_board_info。這個代碼會把spi_board_info注冊要鏈表board_list上。

事實上上文提到的spi_master的注冊會在spi_register_board_info之后，spi_master注冊的過程中會調用scan_boardinfo掃描board_list，找到掛接在它上面的spi設備，然后創建并注冊spi_device。

點擊(此處)折疊或打開

static void scan_boardinfo(struct spi_master?*master)

{

struct boardinfo?*bi;

mutex_lock(&board_lock);

list_for_each_entry(bi,?&board_list,?list)?{

struct spi_board_info?*chip?=?bi->board_info;

unsigned n;

for?(n?=?bi->n_board_info;?n?>?0;?n--,?chip++)?{

if?(chip->bus_num?!=?master->bus_num)

continue;

/*?NOTE:?this relies?on?spi_new_device?to

*?issue diagnostics when given bogus inputs

*/

(void)?spi_new_device(master,?chip);?//創建并注冊了spi_device

}

}

mutex_unlock(&board_lock);

}

6、spi_driver

本文先以linux內核中的/driver/mtd/devices/m25p80.c驅動為參考。

點擊(此處)折疊或打開

static struct spi_driver m25p80_driver?=?{?//spi_driver的構建

.driver?=?{

.name?=?"m25p80",

.bus?=?&spi_bus_type,

.owner?=?THIS_MODULE,

},

.probe?=?m25p_probe,

.remove?=?__devexit_p(m25p_remove),

*/

};

spi_register_driver(&m25p80_driver);//spi driver的注冊

在有匹配的spi device時，會調用m25p_probe

static?int?__devinit m25p_probe(struct spi_device?*spi)

{

……

}

根據傳入的spi_device參數，可以找到對應的spi_master。接下來就可以利用spi子系統為我們完成數據交互了?？梢詤⒖磎25p80_read函數。要完成傳輸，先理解下面幾個結構的含義：（這兩個結構的定義及詳細注釋參見include/linux/spi/spi.h）

spi_message：描述一次完整的傳輸，即cs信號從高->底->高的傳輸
??????? spi_transfer：多個spi_transfer夠成一個spi_message
??????????????? 舉例說明：m25p80的讀過程如下圖

可以分解為兩個spi_ transfer一個是寫命令，另一個是讀數據。具體實現參見m25p80.c中的m25p80_read函數。下面內容摘取之此函數。

點擊(此處)折疊或打開

struct spi_transfer t[2];?//定義了兩個spi_transfer

struct spi_message m;?//定義了兩個spi_message

spi_message_init(&m);?//初始化其transfers鏈表

t[0].tx_buf?=?flash->command;

t[0].len?=?CMD_SIZE?+?FAST_READ_DUMMY_BYTE;?//定義第一個transfer的寫指針和長度

spi_message_add_tail(&t[0],?&m);?//添加到spi_message

t[1].rx_buf?=?buf;

t[1].len?=?len;?//定義第二個transfer的讀指針和長度

spi_message_add_tail(&t[1],?&m);?//添加到spi_message

flash->command[0]?=?OPCODE_READ;

flash->command[1]?=?from?>>?16;

flash->command[2]?=?from?>>?8;

flash->command[3]?=?from;?//初始化前面寫buf的內容

spi_sync(flash->spi,?&m);?//調用spi_master發送spi_message

//?spi_sync為同步方式發送，還可以用spi_async異步方式，那樣的話，需要設置回調完成函數。

另外你也可以選擇一些封裝好的更容易使用的函數，這些函數可以在include/linux/spi/spi.h文件中找到，如：

extern?int?spi_write_then_read(struct spi_device?*spi,

const?u8?*txbuf,?unsigned n_tx,

u8?*rxbuf,?unsigned n_rx);

這篇博文就到這了，下篇給出一個針對m25p10完整的驅動程序。?


Linux下spi驅動開發之m25p10驅動測試

目標：在華清遠見的FS_S5PC100平臺上編寫一個簡單的spi驅動模塊，在probe階段實現對m25p10的ID號探測、flash擦除、flash狀態讀取、flash寫入、flash讀取等操作。代碼已經經過測試，運行于2.6.35內核。理解下面代碼需要參照m25p10的芯片手冊。其實下面的代碼和處理器沒有太大關系，這也是spi子系統的分層特點。

點擊(此處)折疊或打開

#include??

#include?

#include?

#include?

#include?

#include?

#include?

#include??//?kzalloc

#include?

#define FLASH_PAGE_SIZE 256

/*?Flash Operating Commands?*/

#define CMD_READ_ID 0x9f

#define CMD_WRITE_ENABLE 0x06?

#define CMD_BULK_ERASE 0xc7

#define CMD_READ_BYTES 0x03

#define CMD_PAGE_PROGRAM 0x02

#define CMD_RDSR 0x05?

/*?Status Register bits.?*/

#define SR_WIP 1?/*?Write?in?progress?*/

#define SR_WEL 2?/*?Write enable latch?*/

/*?ID Numbers?*/

#define MANUFACTURER_ID 0x20

#define DEVICE_ID 0x1120

/*?Define max times?to?check status register before we give up.?*/

#define MAX_READY_WAIT_COUNT 100000

#define CMD_SZ 4

struct m25p10a?{

struct spi_device?*spi;

struct mutex lock;

char erase_opcode;

char cmd[?CMD_SZ?];

};

/*

*?Internal Helper functions?

*/

/*

*?Read the status register,?returning its value?in?the?location

*?Return the status register value.

*?Returns negative?if?error?occurred.

*/

static?int?read_sr(struct m25p10a?*flash)

{

ssize_t retval;

u8 code?=?CMD_RDSR;

u8 val;

retval?=?spi_write_then_read(flash->spi,?&code,?1,?&val,?1);

if?(retval?

dev_err(&flash->spi->dev,?"error %d reading SR\n",?(int)?retval);

return retval;

}

return val;

}

/*

*?Service routine?to?read status register?until?ready,?or?timeout occurs.

*?Returns non-zero?if?error.

*/

static?int?wait_till_ready(struct m25p10a?*flash)

{

int?count;

int?sr;

/*?one chip guarantees max 5 msec wait here after page writes,

*?but potentially three seconds?(!)?after page?erase.

*/

for?(count?=?0;?count?

if?((sr?=?read_sr(flash))?

break;

else?if?(!(sr?&?SR_WIP))

return 0;

/*?REVISIT sometimes sleeping would be best?*/

}

printk(?"in (%s): count = %d\n",?count?);

return 1;

}

/*

*?Set?write enable latch with Write Enable command.

*?Returns negative?if?error?occurred.

*/

static inline?int?write_enable(?struct m25p10a?*flash?)

{

flash->cmd[0]?=?CMD_WRITE_ENABLE;

return spi_write(?flash->spi,?flash->cmd,?1?);

}

/*

*?Erase?the whole flash memory

*

*?Returns 0?if?successful,?non-zero otherwise.

*/

static?int?erase_chip(?struct m25p10a?*flash?)

{

/*?Wait?until?finished previous write command.?*/

if?(wait_till_ready(flash))

return?-1;

/*?Send write enable,?then?erase?commands.?*/

write_enable(?flash?);

flash->cmd[0]?=?CMD_BULK_ERASE;

return spi_write(?flash->spi,?flash->cmd,?1?);

}

/*

*?Read an address range from the flash chip.?The address range

*?may be any size provided it?is?within the physical boundaries.

*/

static?int?m25p10a_read(?struct m25p10a?*flash,?loff_t from,?size_t?len,?char?*buf?)

{

int?r_count?=?0,?i;

flash->cmd[0]?=?CMD_READ_BYTES;

flash->cmd[1]?=?from?>>?16;

flash->cmd[2]?=?from?>>?8;

flash->cmd[3]?=?from;

#if?1

struct spi_transfer st[2];

struct spi_message msg;

spi_message_init(?&msg?);

memset(?st,?0,?sizeof(st)?);

flash->cmd[0]?=?CMD_READ_BYTES;

flash->cmd[1]?=?from?>>?16;

flash->cmd[2]?=?from?>>?8;

flash->cmd[3]?=?from;

st[?0?].tx_buf?=?flash->cmd;

st[?0?].len?=?CMD_SZ;

spi_message_add_tail(?&st[0],?&msg?);

st[?1?].rx_buf?=?buf;

st[?1?].len?=?len;

spi_message_add_tail(?&st[1],?&msg?);

mutex_lock(?&flash->lock?);

/*?Wait?until?finished previous write command.?*/

if?(wait_till_ready(flash))?{

mutex_unlock(?&flash->lock?);

return?-1;

}

spi_sync(?flash->spi,?&msg?);

r_count?=?msg.actual_length?-?CMD_SZ;

printk(?"in (%s): read %d bytes\n",?__func__,?r_count?);

for(?i?=?0;?i?

printk(?"0x%02x\n",?buf[?i?]?);

}

mutex_unlock(?&flash->lock?);

#endif

return 0;

}

/*

*?Write an address range?to?the flash chip.?Data must be written?in

*?FLASH_PAGE_SIZE chunks.?The address range may be any size provided

*?it?is?within the physical boundaries.

*/

static?int?m25p10a_write(?struct m25p10a?*flash,?loff_t?to,?size_t?len,?const?char?*buf?)

{

int?w_count?=?0,?i,?page_offset;

struct spi_transfer st[2];

struct spi_message msg;

#if?1

if?(wait_till_ready(flash))?{?//讀狀態，等待ready

mutex_unlock(?&flash->lock?);

return?-1;

}

#endif

write_enable(?flash?);?//寫使能?

spi_message_init(?&msg?);

memset(?st,?0,?sizeof(st)?);

flash->cmd[0]?=?CMD_PAGE_PROGRAM;

flash->cmd[1]?=?to?>>?16;

flash->cmd[2]?=?to?>>?8;

flash->cmd[3]?=?to;

st[?0?].tx_buf?=?flash->cmd;

st[?0?].len?=?CMD_SZ;

spi_message_add_tail(?&st[0],?&msg?);

st[?1?].tx_buf?=?buf;

st[?1?].len?=?len;

spi_message_add_tail(?&st[1],?&msg?);

mutex_lock(?&flash->lock?);

/*?get?offset address inside a page?*/

page_offset?=?to?%?FLASH_PAGE_SIZE;

/*?do?all the bytes fit onto one page??*/

if(?page_offset?+?len?<=?FLASH_PAGE_SIZE?)?{?//?yes

st[?1?].len?=?len;

printk("%d, cmd = %d\n",?st[?1?].len,?*(char?*)st[0].tx_buf);

//while(1)

{

spi_sync(?flash->spi,?&msg?);

}

w_count?=?msg.actual_length?-?CMD_SZ;

}

else?{?//?no

}

printk(?"in (%s): write %d bytes to flash in total\n",?__func__,?w_count?);

mutex_unlock(?&flash->lock?);

return 0;

}

static?int?check_id(?struct m25p10a?*flash?)

{

char buf[10]?=?{0};

flash->cmd[0]?=?CMD_READ_ID;

spi_write_then_read(?flash->spi,?flash->cmd,?1,?buf,?3?);

printk(?"Manufacture ID: 0x%x\n",?buf[0]?);

printk(?"Device ID: 0x%x\n",?buf[1]?|?buf[2]?<

return buf[2]?<

}

static?int?m25p10a_probe(struct spi_device?*spi)

{

int?ret?=?0;

struct m25p10a?*flash;

char buf[?256?];

printk(?"%s was called\n",?__func__?);

flash?=?kzalloc(?sizeof(struct m25p10a),?GFP_KERNEL?);

if(?!flash?)?{

return?-ENOMEM;

}

flash->spi?=?spi;

mutex_init(?&flash->lock?);

/*?save flash as driver's?private?data?*/

spi_set_drvdata(?spi,?flash?);

check_id(?flash?);?//讀取ID

#if?1

ret?=?erase_chip(?flash?);?//擦除?

if(?ret?

printk(?"erase the entirely chip failed\n"?);

}

printk(?"erase the whole chip done\n"?);

memset(?buf,?0x7,?256?);

m25p10a_write(?flash,?0,?20,?buf);?//0地址寫入20個7

memset(?buf,?0,?256?);

m25p10a_read(?flash,?0,?25,?buf?);?//0地址讀出25個數?

#endif

return 0;

}

static?int?m25p10a_remove(struct spi_device?*spi)

{

return 0;

}

static struct spi_driver m25p10a_driver?=?{

.probe?=?m25p10a_probe,

.remove?=?m25p10a_remove,

.driver?=?{

.name?=?"m25p10a",

},

};

static?int?__init m25p10a_init(void)

{

return spi_register_driver(&m25p10a_driver);

}

static void __exit m25p10a_exit(void)

{

spi_unregister_driver(&m25p10a_driver);

}

module_init(m25p10a_init);

module_exit(m25p10a_exit);

MODULE_DESCRIPTION("m25p10a driver for FS_S5PC100");

MODULE_LICENSE("GPL");

例。

二、SPI總線協議簡介

介紹驅動開發前，需要先熟悉下SPI通訊協議中的幾個關鍵的地方，后面在編寫驅動時，需要考慮相關因素。

SPI總線由MISO（串行數據輸入）、MOSI（串行數據輸出）、SCK（串行移位時鐘）、CS（使能信號）4個信號線組成。如FS_S5PC100上的M25P10芯片接線為：

上圖中M25P10的D腳為它的數據輸入腳，Q為數據輸出腳，C為時鐘腳。

SPI常用四種數據傳輸模式，主要差別在于：輸出串行同步時鐘極性（CPOL）和相位（CPHA）可以進行配置。如果CPOL= 0，串行同步時鐘的空閑狀態為低電平；如果CPOL= 1，串行同步時鐘的空閑狀態為高電平。如果CPHA= 0，在串行同步時鐘的前沿（上升或下降）數據被采樣；如果CPHA = 1，在串行同步時鐘的后沿（上升或下降）數據被采樣。

這四種模式中究竟選擇哪種模式取決于設備。如M25P10的手冊中明確它可以支持的兩種模式為：CPOL=0 CPHA=0? 和 CPOL=1 CPHA=1

三、linux下SPI驅動開發

首先明確SPI驅動層次，如下圖：???????

我們以上面的這個圖為思路

1、 Platform bus

Platform bus對應的結構是platform_bus_type，這個內核開始就定義好的。我們不需要定義。

2、Platform_device

SPI控制器對應platform_device的定義方式，同樣以S5PC100中的SPI控制器為例，參看arch/arm/plat-s5pc1xx/dev-spi.c文件

點擊(此處)折疊或打開

struct platform_device s3c_device_spi0?=?{

.name?=?"s3c64xx-spi",?//名稱，要和Platform_driver匹配

.id?=?0,?//第0個控制器，S5PC100中有3個控制器

.num_resources?=?ARRAY_SIZE(s5pc1xx_spi0_resource),?//占用資源的種類

.resource?=?s5pc1xx_spi0_resource,?//指向資源結構數組的指針

.dev?=?{

.dma_mask?=?&spi_dmamask,?//dma尋址范圍?

.coherent_dma_mask?=?DMA_BIT_MASK(32),?//可以通過關閉cache等措施保證一致性的dma尋址范圍

.platform_data?=?&s5pc1xx_spi0_pdata,?//特殊的平臺數據，參看后文

},

};

static struct s3c64xx_spi_cntrlr_info s5pc1xx_spi0_pdata?=?{

.cfg_gpio?=?s5pc1xx_spi_cfg_gpio,?//用于控制器管腳的IO配置

.fifo_lvl_mask?=?0x7f,

.rx_lvl_offset?=?13,

};

static?int?s5pc1xx_spi_cfg_gpio(struct platform_device?*pdev)

{

switch?(pdev->id)?{

case?0:

s3c_gpio_cfgpin(S5PC1XX_GPB(0),?S5PC1XX_GPB0_SPI_MISO0);

s3c_gpio_cfgpin(S5PC1XX_GPB(1),?S5PC1XX_GPB1_SPI_CLK0);

s3c_gpio_cfgpin(S5PC1XX_GPB(2),?S5PC1XX_GPB2_SPI_MOSI0);

s3c_gpio_setpull(S5PC1XX_GPB(0),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPB(1),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPB(2),?S3C_GPIO_PULL_UP);

break;

case?1:

s3c_gpio_cfgpin(S5PC1XX_GPB(4),?S5PC1XX_GPB4_SPI_MISO1);

s3c_gpio_cfgpin(S5PC1XX_GPB(5),?S5PC1XX_GPB5_SPI_CLK1);

s3c_gpio_cfgpin(S5PC1XX_GPB(6),?S5PC1XX_GPB6_SPI_MOSI1);

s3c_gpio_setpull(S5PC1XX_GPB(4),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPB(5),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPB(6),?S3C_GPIO_PULL_UP);

break;

case?2:

s3c_gpio_cfgpin(S5PC1XX_GPG3(0),?S5PC1XX_GPG3_0_SPI_CLK2);

s3c_gpio_cfgpin(S5PC1XX_GPG3(2),?S5PC1XX_GPG3_2_SPI_MISO2);

s3c_gpio_cfgpin(S5PC1XX_GPG3(3),?S5PC1XX_GPG3_3_SPI_MOSI2);

s3c_gpio_setpull(S5PC1XX_GPG3(0),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPG3(2),?S3C_GPIO_PULL_UP);

s3c_gpio_setpull(S5PC1XX_GPG3(3),?S3C_GPIO_PULL_UP);

break;

default:

dev_err(&pdev->dev,?"Invalid SPI Controller number!");

return?-EINVAL;

}

3、Platform_driver

再看platform_driver，參看drivers/spi/spi_s3c64xx.c文件

點擊(此處)折疊或打開

static struct platform_driver s3c64xx_spi_driver?=?{

.driver?=?{

.name?=?"s3c64xx-spi",?//名稱，和platform_device對應

.owner?=?THIS_MODULE,

},

.remove?=?s3c64xx_spi_remove,

.suspend?=?s3c64xx_spi_suspend,

.resume?=?s3c64xx_spi_resume,

};

platform_driver_probe(&s3c64xx_spi_driver,?s3c64xx_spi_probe)；//注冊s3c64xx_spi_driver

和平臺中注冊的platform_device匹配后，調用s3c64xx_spi_probe。然后根據傳入的platform_device參數，構建一個用于描述SPI控制器的結構體spi_master，并注冊。spi_register_master(master)。后續注冊的spi_device需要選定自己的spi_master，并利用spi_master提供的傳輸功能傳輸spi數據。

和I2C類似，SPI也有一個描述控制器的對象叫spi_master。其主要成員是主機控制器的序號（系統中可能存在多個SPI主機控制器）、片選數量、SPI模式和時鐘設置用到的函數、數據傳輸用到的函數等。

點擊(此處)折疊或打開

struct spi_master?{

struct device dev;

s16 bus_num;?//表示是SPI主機控制器的編號。由平臺代碼決定

u16 num_chipselect;?//控制器支持的片選數量，即能支持多少個spi設備

int?(*setup)(struct spi_device?*spi);?//針對設備設置SPI的工作時鐘及數據傳輸模式等。在spi_add_device函數中調用。

int?(*transfer)(struct spi_device?*spi,

struct spi_message?*mesg);?//實現數據的雙向傳輸，可能會睡眠

void?(*cleanup)(struct spi_device?*spi);?//注銷時調用

};

4、Spi bus

Spi總線對應的總線類型為spi_bus_type，在內核的drivers/spi/spi.c中定義

點擊(此處)折疊或打開

struct bus_type spi_bus_type?=?{

.name?=?"spi",

.dev_attrs?=?spi_dev_attrs,

.match?=?spi_match_device,

.uevent?=?spi_uevent,

.suspend?=?spi_suspend,

.resume?=?spi_resume,

};

對應的匹配規則是（高版本中的匹配規則會稍有變化，引入了id_table，可以匹配多個spi設備名稱）：

點擊(此處)折疊或打開

static?int?spi_match_device(struct device?*dev,?struct device_driver?*drv)

{

const?struct spi_device?*spi?=?to_spi_device(dev);

return strcmp(spi->modalias,?drv->name)?==?0;

}

5、spi_device

下面該講到spi_device的構建與注冊了。spi_device對應的含義是掛接在spi總線上的一個設備，所以描述它的時候應該明確它自身的設備特性、傳輸要求、及掛接在哪個總線上。

點擊(此處)折疊或打開

static struct spi_board_info s3c_spi_devs[]?__initdata?=?{

{

.modalias?=?"m25p10",

.mode?=?SPI_MODE_0,?//CPOL=0,?CPHA=0 此處選擇具體數據傳輸模式

.max_speed_hz?=?10000000,?//最大的spi時鐘頻率

/*?Connected?to?SPI-0 as 1st Slave?*/

.bus_num?=?0,?//設備連接在spi控制器0上

.chip_select?=?0,?//片選線號，在S5PC100的控制器驅動中沒有使用它作為片選的依據，而是選擇了下文controller_data里的方法。

.controller_data?=?&smdk_spi0_csi[0],

},

};

static struct s3c64xx_spi_csinfo smdk_spi0_csi[]?=?{

[0]?=?{

.set_level?=?smdk_m25p10_cs_set_level,

.fb_delay?=?0x3,

},

};

static void smdk_m25p10_cs_set_level(int?high)?//spi控制器會用這個方法設置cs

{

u32 val;

val?=?readl(S5PC1XX_GPBDAT);

if?(high)

val?|=?(1<<3);

else

val?&=?~(1<<3);

writel(val,?S5PC1XX_GPBDAT);

}

spi_register_board_info(s3c_spi_devs,?ARRAY_SIZE(s3c_spi_devs));//注冊spi_board_info。這個代碼會把spi_board_info注冊要鏈表board_list上。

事實上上文提到的spi_master的注冊會在spi_register_board_info之后，spi_master注冊的過程中會調用scan_boardinfo掃描board_list，找到掛接在它上面的spi設備，然后創建并注冊spi_device。

點擊(此處)折疊或打開

static void scan_boardinfo(struct spi_master?*master)

{

struct boardinfo?*bi;

mutex_lock(&board_lock);

list_for_each_entry(bi,?&board_list,?list)?{

struct spi_board_info?*chip?=?bi->board_info;

unsigned n;

for?(n?=?bi->n_board_info;?n?>?0;?n--,?chip++)?{

if?(chip->bus_num?!=?master->bus_num)

continue;

/*?NOTE:?this relies?on?spi_new_device?to

*?issue diagnostics when given bogus inputs

*/

(void)?spi_new_device(master,?chip);?//創建并注冊了spi_device

}

}

mutex_unlock(&board_lock);

}

6、spi_driver

本文先以linux內核中的/driver/mtd/devices/m25p80.c驅動為參考。

點擊(此處)折疊或打開

static struct spi_driver m25p80_driver?=?{?//spi_driver的構建

.driver?=?{

.name?=?"m25p80",

.bus?=?&spi_bus_type,

.owner?=?THIS_MODULE,

},

.probe?=?m25p_probe,

.remove?=?__devexit_p(m25p_remove),

*/

};

spi_register_driver(&m25p80_driver);//spi driver的注冊

在有匹配的spi device時，會調用m25p_probe

static?int?__devinit m25p_probe(struct spi_device?*spi)

{

……

}

根據傳入的spi_device參數，可以找到對應的spi_master。接下來就可以利用spi子系統為我們完成數據交互了?？梢詤⒖磎25p80_read函數。要完成傳輸，先理解下面幾個結構的含義：（這兩個結構的定義及詳細注釋參見include/linux/spi/spi.h）

spi_message：描述一次完整的傳輸，即cs信號從高->底->高的傳輸
??????? spi_transfer：多個spi_transfer夠成一個spi_message
??????????????? 舉例說明：m25p80的讀過程如下圖

可以分解為兩個spi_ transfer一個是寫命令，另一個是讀數據。具體實現參見m25p80.c中的m25p80_read函數。下面內容摘取之此函數。

點擊(此處)折疊或打開

struct spi_transfer t[2];?//定義了兩個spi_transfer

struct spi_message m;?//定義了兩個spi_message

spi_message_init(&m);?//初始化其transfers鏈表

t[0].tx_buf?=?flash->command;

t[0].len?=?CMD_SIZE?+?FAST_READ_DUMMY_BYTE;?//定義第一個transfer的寫指針和長度

spi_message_add_tail(&t[0],?&m);?//添加到spi_message

t[1].rx_buf?=?buf;

t[1].len?=?len;?//定義第二個transfer的讀指針和長度

spi_message_add_tail(&t[1],?&m);?//添加到spi_message

flash->command[0]?=?OPCODE_READ;

flash->command[1]?=?from?>>?16;

flash->command[2]?=?from?>>?8;

flash->command[3]?=?from;?//初始化前面寫buf的內容

spi_sync(flash->spi,?&m);?//調用spi_master發送spi_message

//?spi_sync為同步方式發送，還可以用spi_async異步方式，那樣的話，需要設置回調完成函數。

另外你也可以選擇一些封裝好的更容易使用的函數，這些函數可以在include/linux/spi/spi.h文件中找到，如：

extern?int?spi_write_then_read(struct spi_device?*spi,

const?u8?*txbuf,?unsigned n_tx,

u8?*rxbuf,?unsigned n_rx);

這篇博文就到這了，下篇給出一個針對m25p10完整的驅動程序。?


Linux下spi驅動開發之m25p10驅動測試

目標：在華清遠見的FS_S5PC100平臺上編寫一個簡單的spi驅動模塊，在probe階段實現對m25p10的ID號探測、flash擦除、flash狀態讀取、flash寫入、flash讀取等操作。代碼已經經過測試，運行于2.6.35內核。理解下面代碼需要參照m25p10的芯片手冊。其實下面的代碼和處理器沒有太大關系，這也是spi子系統的分層特點。

點擊(此處)折疊或打開

#include??

#include?

#include?

#include?

#include?

#include?

#include?

#include??//?kzalloc

#include?

#define FLASH_PAGE_SIZE 256

/*?Flash Operating Commands?*/

#define CMD_READ_ID 0x9f

#define CMD_WRITE_ENABLE 0x06?

#define CMD_BULK_ERASE 0xc7

#define CMD_READ_BYTES 0x03

#define CMD_PAGE_PROGRAM 0x02

#define CMD_RDSR 0x05?

/*?Status Register bits.?*/

#define SR_WIP 1?/*?Write?in?progress?*/

#define SR_WEL 2?/*?Write enable latch?*/

/*?ID Numbers?*/

#define MANUFACTURER_ID 0x20

#define DEVICE_ID 0x1120

/*?Define max times?to?check status register before we give up.?*/

#define MAX_READY_WAIT_COUNT 100000

#define CMD_SZ 4

struct m25p10a?{

struct spi_device?*spi;

struct mutex lock;

char erase_opcode;

char cmd[?CMD_SZ?];

};

/*

*?Internal Helper functions?

*/

/*

*?Read the status register,?returning its value?in?the?location

*?Return the status register value.

*?Returns negative?if?error?occurred.

*/

static?int?read_sr(struct m25p10a?*flash)

{

ssize_t retval;

u8 code?=?CMD_RDSR;

u8 val;

retval?=?spi_write_then_read(flash->spi,?&code,?1,?&val,?1);

if?(retval?

dev_err(&flash->spi->dev,?"error %d reading SR\n",?(int)?retval);

return retval;

}

return val;

}

/*

*?Service routine?to?read status register?until?ready,?or?timeout occurs.

*?Returns non-zero?if?error.

*/

static?int?wait_till_ready(struct m25p10a?*flash)

{

int?count;

int?sr;

/*?one chip guarantees max 5 msec wait here after page writes,

*?but potentially three seconds?(!)?after page?erase.

*/

for?(count?=?0;?count?

if?((sr?=?read_sr(flash))?

break;

else?if?(!(sr?&?SR_WIP))

return 0;

/*?REVISIT sometimes sleeping would be best?*/

}

printk(?"in (%s): count = %d\n",?count?);

return 1;

}

/*

*?Set?write enable latch with Write Enable command.

*?Returns negative?if?error?occurred.

*/

static inline?int?write_enable(?struct m25p10a?*flash?)

{

flash->cmd[0]?=?CMD_WRITE_ENABLE;

return spi_write(?flash->spi,?flash->cmd,?1?);

}

/*

*?Erase?the whole flash memory

*

*?Returns 0?if?successful,?non-zero otherwise.

*/

static?int?erase_chip(?struct m25p10a?*flash?)

{

/*?Wait?until?finished previous write command.?*/

if?(wait_till_ready(flash))

return?-1;

/*?Send write enable,?then?erase?commands.?*/

write_enable(?flash?);

flash->cmd[0]?=?CMD_BULK_ERASE;

return spi_write(?flash->spi,?flash->cmd,?1?);

}

/*

*?Read an address range from the flash chip.?The address range

*?may be any size provided it?is?within the physical boundaries.

*/

static?int?m25p10a_read(?struct m25p10a?*flash,?loff_t from,?size_t?len,?char?*buf?)

{

int?r_count?=?0,?i;

flash->cmd[0]?=?CMD_READ_BYTES;

flash->cmd[1]?=?from?>>?16;

flash->cmd[2]?=?from?>>?8;

flash->cmd[3]?=?from;

#if?1

struct spi_transfer st[2];

struct spi_message msg;

spi_message_init(?&msg?);

memset(?st,?0,?sizeof(st)?);

flash->cmd[0]?=?CMD_READ_BYTES;

flash->cmd[1]?=?from?>>?16;

flash->cmd[2]?=?from?>>?8;

flash->cmd[3]?=?from;

st[?0?].tx_buf?=?flash->cmd;

st[?0?].len?=?CMD_SZ;

spi_message_add_tail(?&st[0],?&msg?);

st[?1?].rx_buf?=?buf;

st[?1?].len?=?len;

spi_message_add_tail(?&st[1],?&msg?);

mutex_lock(?&flash->lock?);

/*?Wait?until?finished previous write command.?*/

if?(wait_till_ready(flash))?{

mutex_unlock(?&flash->lock?);

return?-1;

}

spi_sync(?flash->spi,?&msg?);

r_count?=?msg.actual_length?-?CMD_SZ;

printk(?"in (%s): read %d bytes\n",?__func__,?r_count?);

for(?i?=?0;?i?

printk(?"0x%02x\n",?buf[?i?]?);

}

mutex_unlock(?&flash->lock?);

#endif

return 0;

}

/*

*?Write an address range?to?the flash chip.?Data must be written?in

*?FLASH_PAGE_SIZE chunks.?The address range may be any size provided

*?it?is?within the physical boundaries.

*/

static?int?m25p10a_write(?struct m25p10a?*flash,?loff_t?to,?size_t?len,?const?char?*buf?)

{

int?w_count?=?0,?i,?page_offset;

struct spi_transfer st[2];

struct spi_message msg;

#if?1

if?(wait_till_ready(flash))?{?//讀狀態，等待ready

mutex_unlock(?&flash->lock?);

return?-1;

}

#endif

write_enable(?flash?);?//寫使能?

spi_message_init(?&msg?);

memset(?st,?0,?sizeof(st)?);

flash->cmd[0]?=?CMD_PAGE_PROGRAM;

flash->cmd[1]?=?to?>>?16;

flash->cmd[2]?=?to?>>?8;

flash->cmd[3]?=?to;

st[?0?].tx_buf?=?flash->cmd;

st[?0?].len?=?CMD_SZ;

spi_message_add_tail(?&st[0],?&msg?);

st[?1?].tx_buf?=?buf;

st[?1?].len?=?len;

spi_message_add_tail(?&st[1],?&msg?);

mutex_lock(?&flash->lock?);

/*?get?offset address inside a page?*/

page_offset?=?to?%?FLASH_PAGE_SIZE;

/*?do?all the bytes fit onto one page??*/

if(?page_offset?+?len?<=?FLASH_PAGE_SIZE?)?{?//?yes

st[?1?].len?=?len;

printk("%d, cmd = %d\n",?st[?1?].len,?*(char?*)st[0].tx_buf);

//while(1)

{

spi_sync(?flash->spi,?&msg?);

}

w_count?=?msg.actual_length?-?CMD_SZ;

}

else?{?//?no

}

printk(?"in (%s): write %d bytes to flash in total\n",?__func__,?w_count?);

mutex_unlock(?&flash->lock?);

return 0;

}

static?int?check_id(?struct m25p10a?*flash?)

{

char buf[10]?=?{0};

flash->cmd[0]?=?CMD_READ_ID;

spi_write_then_read(?flash->spi,?flash->cmd,?1,?buf,?3?);

printk(?"Manufacture ID: 0x%x\n",?buf[0]?);

printk(?"Device ID: 0x%x\n",?buf[1]?|?buf[2]?<

return buf[2]?<

}

static?int?m25p10a_probe(struct spi_device?*spi)

{

int?ret?=?0;

struct m25p10a?*flash;

char buf[?256?];

printk(?"%s was called\n",?__func__?);

flash?=?kzalloc(?sizeof(struct m25p10a),?GFP_KERNEL?);

if(?!flash?)?{

return?-ENOMEM;

}

flash->spi?=?spi;

mutex_init(?&flash->lock?);

/*?save flash as driver's?private?data?*/

spi_set_drvdata(?spi,?flash?);

check_id(?flash?);?//讀取ID

#if?1

ret?=?erase_chip(?flash?);?//擦除?

if(?ret?

printk(?"erase the entirely chip failed\n"?);

}

printk(?"erase the whole chip done\n"?);

memset(?buf,?0x7,?256?);

m25p10a_write(?flash,?0,?20,?buf);?//0地址寫入20個7

memset(?buf,?0,?256?);

m25p10a_read(?flash,?0,?25,?buf?);?//0地址讀出25個數?

#endif

return 0;

}

static?int?m25p10a_remove(struct spi_device?*spi)

{

return 0;

}

static struct spi_driver m25p10a_driver?=?{

.probe?=?m25p10a_probe,

.remove?=?m25p10a_remove,

.driver?=?{

.name?=?"m25p10a",

},

};

static?int?__init m25p10a_init(void)

{

return spi_register_driver(&m25p10a_driver);

}

static void __exit m25p10a_exit(void)

{

spi_unregister_driver(&m25p10a_driver);

}

module_init(m25p10a_init);

module_exit(m25p10a_exit);

MODULE_DESCRIPTION("m25p10a driver for FS_S5PC100");

MODULE_LICENSE("GPL");

?